Planet Technology FT-90X FT-902 Manuel d'utilisateur

User's Manual FT-902 FT-902S15/S35/S50 FT-905A FT-906A20/906B20 10/100Base-TX to 100Base-FX Web Smart Media Converter

-7- 2.2 Install the Converter This section describes how to install your FT-90X Web Smart Media Converter and make connections to the converter. Plea

-8- #Note: Please refers to APPENDIX-A for detailed wiring information of the FT-90X. To prevent from optic acceptor malfunction, check the both wire

-9- 2.2.2 Chassis Installation and Rack Mounting To install the media converter in a 10-inch or 19-inch with standard rack, follow the instructions d

-10- Figure 2-2 Mounting the Chassis in a Rack

-11- 3. WEB MANAGEMENT This chapter describes how to manage the FT-90X. Topics include: - Overview - Management methods - Assigning an IP address

-12- 3.2.2 Login the media converter Before you start configure the FT-90X, please note the FT-90X is configured through an Ethernet connection, make

-13- 4. CONFIGURATION The FT-90X Web Smart Media Converter provide Web interface for Media converter smart function configuration and make the Media

-14- 4.2 System 4.2.1 System Information The System Information page provides information for the current device. System Info page helps a network ma

-15- 4.2.2 IP Configuration The IP Configuration includes the IP Address, Subnet Mask and Gateway. The screen in Figure 4-3 appears. Figure 4-3 IP C

-16- 4.2.3 Password Setting This function provides administrator to secure Web login. The screen in Figure 4-4 appears. Figure 4-4 Password Setting

-2- Trademarks Copyright © PLANET Technology Corp. 2007. Contents subject to which revision without prior notice. PLANET is a registered trademark of

-17- 4.3 Port Configuration This function allows displaying each port’s status. The Link Status in the screen displays the current connection speed

-18- Default value: No Limit The Ingress Rate Limit configuration field as show in Figure 4-6. • Egress Shaping The value of outbound traffic limita

-19- Figure 4-7 Port Configuration-Egress Shaping screen

-20- 4.4 Converter Configuration This page allows setup Management Port, Loop Back Reply, Broadcast Storm Control, Class of Services and LLR Mode. Pr

-21- • First In First Out • Strict Priority • Weighted Round Robin • WRR Priority (High: Low) This field is available when choose Weighted Round Rob

-22- When multiple CoS schemes are enabled, the data packet is treated as the high priority as long as any one of three CoS schemes is mapped to “hig

-23- Management Switch/Hub Media Media Switch/Hub Management Station w/SNMP Converter

-24- 4.5 Converter Status The page shows the converter’s copper and fiber linking status. The screen in Figure 4-11 appears. Figure 4-11 Converter S

-25- 4.6 Statistics The Port Statistic page displays the status of packet count from copper port and fiber port. The Port statistics screen in Figure

-26- Received device was last refreshed • CRC Align Errors which displays the number of CRC and Align errors that have occurred on the interface sinc

-3- TABLE OF CONTENTS 1. INTRODUCTION...

-27- 4.7 Tools This section provides tools of FT-90x. As listed at the left of the main screen, the configurable smart functions are shown as below:

-28- Figure 4-13 Loop Back Test screen The Loop Back Test Parameters includes the following fields: • Send Packet Number Enter the number of loop b

-29- Figure 4-15 Loop Back Reply /Enable screen 4.7.2 System Reboot The Reboot page enables the device to be rebooted from a remote location. Onc

-30- Figure 4-17 Tools\Configuration Setting screen Backup All current configurations (except IP Configuration) will save to converter as backu

-31- Figure 4-20 Configuration restore screen Factory Reset The Factory Reset button can reset the FT-90x back to the factory default mode. Be a

-32- 4.7.4 Firmware Upgrade The Firmware Upgrade page contains fields for downloading system image files from the Local File browser to the device.

-33- Figure 4-24 Firmware Upgrade screen Click the “Browse” button of the main page, the system would pop up the file selection menu to choose firm

-34- Figure 4-27 Software successfully loaded notice screen "Note: Do not power off the converter until the update progress is complete. &qu

-35- 5. TROUBLESHOOTING This chapter contains information to help you solve problems. If the media converter is not functioning properly, make sure t

-36- APPENDIX A A.1 Device‘s RJ-45 Pin Assignments 10/100Mbps, 10/100Base-TX Contact MDI MDI-X 1 1 (TX +) 3 2 2 (TX -) 6 3 3 (RX +) 1 6 6

-1- 1. INTRODUCTION 1.1 Package Contents Check the contents of your package for following parts: ● Web Smart Media Converter x1 ● CD-ROM user'

-37- A.3 Fiber Optical Cable Connection Parameter The wiring details are as below: Fiber Optical patch Cables: Standard Fiber Type Cable Specific

-2- ; Supports Bandwidth Control (Kbps) for both Ingress and Egress ; Supports Broadcast Storm Control to optimize network bandwidth. ; Supports Ethe

-3- 2. INSTALLATION This section describes the functionalities of FT-90X’s components and guides how to install it on the desktop or shelf. Basic kno

-4- 2.1.1 FT-90X Front Panel Figure 2-1, 2-2 & 2-3 shows a front panel of FT-90X. Figure 2-1 PLANET FT-902/FT-902S Front Panel Figure 2-2 PLA

-5- 2.1.2 LED Indicators System LED Color Function PWR Green Lit: Power on. 10/100Base-TX Port LED Color Function Lit: Indicate that the port i

-6- 2.1.3 FT-90X Rear Panel The rear panel of the converter indicates one DC jack, which accepts input power with 5V DC 2A. FT-90x series Figure