Planet Technology WAP-4060PE Manuel d'utilisateur

54/108Mbps Super G Wireless LAN Managed Access Point WAP-4060PE User’s Manual

5 Moreover, the original antenna of WAP-4060PE can be replaced with other external an-tennas to extend the coverage. Please check the specification o

6 Chapter 2 Installation 2.1 General Installation Before you proceed with the installation, it is necessary that you have enough informa-tion about t

7 Chapter 3 Access Point Setup 3.1 Overview This chapter describes the setup procedure to make the WAP-4060PE a valid device on your LAN, and to func

8 IP address The IP address for the WAP-4060PE. MAC Address The hardware or physical address of the WAP-4060PE. IEEE Standard The wireless standard o

9 These are the default values. The password can and should be changed. Always enter the current user name and password, as set on the Admin Login sc

10 3.4 Access Control This feature allows you to block certain access from unknown or distrusted wireless stations. Click Access Control on the menu

11 Data - Trusted Wireless Stations Trusted Wireless Stations Here lists ass Wireless Stations which you have designated as “Trusted”. Other Wireles

12 Add To add a Trusted Station which is not in the "Other Wireless Stations" list, enter the required data and click this button. Clear Cl

13 Data - Security Profiles Screen Profile Profile List All available profiles are listed. For each profile, the following data is displayed: · *

14 802.11b/g Bridge Mode Select the primary profile for 802.11b and 802.11g Bridge Mode. This setting determines the SSID and security settings used

ii Copyright Copyrightã 2005 by PLANET Technology Corp. All rights reserved. No part of this publica-tion may be reproduced, transmitted, transcrib

15 Data - VLAN Configuation Screen VLAN – Client Traffic Profile Each profile is listed, whether currently enabled or not. You can assign traffic

16 Specified VLAN ID If selected, you can enter the desired VLAN ID. Normally, this ID should be one of the client VLAN IDs defined above. 3.6 Confi

17 If this option is selected: · This WAP-4060PE must have a "client login" on the Radius Server. · Each user must have a "user lo

18 the Security page, or the Radius-based MAC authentication sub-screen, de-pending on the security method used. · On the WAP-4060PE, enable the Rad

19 WEP Key Index If this field is visible, select the desired key index. Any value can be used, provided it matches the value on the Radius Server.

20 · Ensure the WAP-4060PE has the correct address, port number, and shared key for login to your Radius Server. These parameters are entered either

21 Data - UAM Screen Enable Enable this if you want to use this feature. See the section above for details of using UAM. Internal Web-based Authent

22 Data - WEP Screen WEP Data Encryption Select the desired option, and ensure your Wireless stations have the identical setting: · 64 Bit Encrypt

23 Passphrase Use this to generate a key or keys, instead of entering them directly. Enter a word or group of printable characters in the Passphrase

24 · TKIP - Unicast (point-to-point) transmissions are en-crypted using TKIP, and multicast (broadcast) transmissions are not encrypted. · TKIP +

iii R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCI

25 Data - WPA-802.1x Screen WPA-802.1x Radius Server Address Enter the name or IP address of the Radius Server on your network. Radius Port Enter th

26 WPA Encryption Select the desired option. Other Wireless Stations must use the same method. · TKIP - Unicast (point-to-point) transmissions are e

27 3.6.9 Security Settings - 802.1x This uses the 802.1x standard for client authentication, and WEP for data encryption. If possible, you should use

28 WEP Key Size Select the desired option: · 64 Bit - Keys are 10 Hex (5 ASCII) characters. · 128 Bit - Keys are 26 Hex (13 ASCII) characters. ·

29 3.7 System Screen Click System on the menu to view a screen like the following. Data - System Screen Identification Access Point Name Enter a sui

30 WINS Enable WINS If your LAN has a WINS server, you can enable this to have this AP register with the WINS server. WINS Server Name/IP Ad-dress En

31 Data - Basic Settings Screen Operation Wireless Mode Select the desired option: · Disable - select this if for some reason you do not want this

32 AP Mode Both Bridge mode and AP mode can be used simultaneously, unless AP mode is "Client/Repeater". Select the desired AP mode: · No

33 In PTMP mode, only allow specified APs This is only functional if using Point-to-Multi-Point Bridge (PTMP) mode. If enabled, you can specify the M

34 Data - Advanced Settings Screen Basic Rate Basic Rate The Basic Rate is used for broadcasting. It does not determine the data transmission rate,

i TABLE OF CONTENTS CHAPTER 1 INTRODUCTION...1 1.1 Package Contents...

35 RTS/CTS Threshold Enter the preferred setting between 256 and 2346. Nor-mally, this can be left at the default value. Preamble Type Select the des

36 Chapter 4 PC and Server Configuration 4.1 Overview All Wireless Stations need to have settings which match the Wireless Access Point. These settin

37 Security · The Pre-shared Key entered on the WAP-4060PE must also be entered on each Wireless client. · The Encryption method (e.g. TKIP, AES) m

38 · dhcpd · dns · rras · webserver (IIS) · Radius Server (Internet Authentication Service) · Certificate Authority 4.5.1 Windows 2000 Dom

39 6. Enter the information for the Certificate Authority, and click Next. 7. Click Next if you don't want to change the CA's configurat

40 3. Click Next when the New Scope Wizard Begins. 4. Enter the name and description for the scope, click Next. 5. Define the IP address range. Ch

41 11. If you don't want a WINS server, just click Next. 12. Select Yes, I want to activate this scope now. Click Next, then Finish. 13. Righ

42 4. Select Start - Programs - Administrative Tools - Active Directory Users and Com-puters. 5. Right-click on your active directory domain, and se

43 7. Select Computer Configuration - Windows Settings - Security Settings - Public Key Policies, right-click Automatic Certificate Request Settings

44 10. Ensure that your certificate authority is checked, then click Next. 11. Review the policy change information and click Finish. 12. Click St

ii 4.6.2 802.1x Authentication Setup...49 4.7 Using 802.1x Mode (without WPA)...

45 9. Click Permitted, then OK. Select Next. 10. Select Grant remote access permission. Click Next. 11. Click Edit Profile... and select the Authen

46 3. Select the Dial-in tab, and enable Allow access. Click OK. 4.6 802.1x Client Setup on Windows XP Windows XP ships with a complete 802.1x cl

47 4. On the first screen (below), select Request a certificate, click Next. 5. Select User certificate request and select User Certificate, the cl

48 6. Click Submit. 7. A message will be displayed, then the certificate will be returned to you. Click Install this certificate.

49 8. . You will receive a confirmation message. Click Yes. 9. Certificate setup is now complete. 4.6.2 802.1x Authentication Setup 1. Open the p

50 Encryption Settings The Encryption settings must match the APs (WAP-4060PE) on the Wireless network you want to join. · Windows XP will detect a

51 2. Select the wireless network from the Available Networks list, and click Configure. 3. Select and enter the correct values, as advised by your

52 4.7 Using 802.1x Mode (without WPA) The procedures are similar to using WPA-802.1x. The only difference is that on your client, you must NOT enabl

53 Chapter 5 Operation and Status 5.1 Operation Once both the WAP-4060PE and the PCs are configured, operation is automatic. However, you may need to

54 Data - Status Screen Access Point Access Point Name The current name will be displayed. MAC Address The MAC (physical) address of the WAP-4060PE.

1 Chapter 1 Introduction WAP-4060PE is an IEEE 802.11g Wireless Access Point with PoE. Catering to the enterprise demands, WAP-4060PE enhances securi

55 5.3.1 Statistics Screen This screen is displayed when the 2.4GHz Statistics button on the Status screen is clicked. It shows details of the traffi

56 Multicast Packets Number of Broadcast packets transmitted to or received from Wireless Stations, using Multicast transmission. Management Number o

57 5.3.3 Activity Log This screen is displayed when the Log button on the Status screen is clicked. Data - Activity Log Data Current Time The system

58 5.3.4 Station List This screen is displayed when the Stations button on the Status screen is clicked. Data - Station List Screen Station List Nam

59 Chapter 6 Management 6.1 Overview This Chapter covers the following features, available on the WAP-4060PE’s Manage-ment menu. · Admin Login · Au

60 Change Admin Pass-word If you wish to change the Admin password, check this field and enter the new login password in the fields below. New Passwo

61 Data - Auto Config/Update Screen Admin Connections Perform Auto Configuration on this AP next restart If checked, this AP will perform Auto Confi

62 Provide "Respond to Auto-configuration" setting If enabled, the "Respond to Auto-configuration" setting on this AP is supplied

63 Data - Config File Screen Backup Save a copy of current settings Once you have the WAP-4060PE working properly, you should back up the settings t

64 6.5 Log Settings (Syslog) If you have a log server on your LAN, this screen allows you to configure the WAP-4060PE to send log data to your log se

2 n Provide Windows-base utility, Web, and CLI (Command Line Interface) Configuration n SNMP support 1.4 Physical Details Front panel STATUS On - Er

65 Data - Rogue AP Screen Enable Detection Enable Detection To use this feature, enable the "Enable Rogue AP De-tection" checkbox, and sel

66 Data - SNMP Screen General Enable SNMP Use this to enable or disable SNMP as required Community Enter the community string, usually either "

67 6.8 Upgrade Firmware The firmware (software) in the Wireless Access Point can be upgraded using your Web Browser. You must first download the upg

68 Appendix A Specifications Model WAP-4060PE Standard IEEE 802.11b, 802.11g Signal Type DSSS (Direct Sequence Spread Spectrum) Modulation OFDM wi

69 Management Web based configuration RADIUS Accounting RADIUS-On feature RADIUS Accounting update CLI Message Log Access Control list file support C

70 Appendix B Troubleshooting Problem 1: Can't connect to the WAP-4060PE to configure it. Solution 1: Check the following: · The WAP-4060PE is

71 Appendix C Command Line Interface If desired, the Command Line Interface (CLI) can be used for configuration. This creates the possibility of crea

72 4. Use the “Connect” command to start the connection. 5. You will be prompted for a user name and password. Enter the current user name and passw

73 get 11gonly Display 11g Only Allowed get 11goptimize Display 11g Optimization Level get 11goverlapbss Display Overlapping BSS Protection get acl

74 get ctstype Display CTS type get domainsuffix Display Domain Name Server suffix get dtim Display Data Beacon Rate (DTIM) get enableANI Disp

3 3. Continue holding the Reset Button until the Status (Red) LED blinks TWICE. 4. Release the Reset Button. The factory default configuration has n

75 get overRidetxpower Display Tx power override get operationMode Display Operation Mode get power Display Transmit Power Setting get quietAckC

76 get wds Display WDS Mode get wep Display Encryption Mode get wirelessmode Display Wireless LAN Mode get 80211d Display 802.11d mode

77 get ftpLogin Display FTP Login Name get ftpPassword Display FTP Password get activeCurrentPro-file Display active Current Profile get profileName

78 get trapRecvIp Display Trap Receiver IP get wdsMacList Display WDS Mac Address List get enableWireless-Client Display Wireless Client Enable/Dis

79 set authentication Set Authentication Type set autochannelse-lect Set Auto Channel Selection set basic11b Set Use of Basic 11b Rates set basic1

80 set fragmentthresh-old Set Fragment Threshold set frequency Set Radio Frequency (MHz) set gateway Set Gateway IP Address set gbeaconrate Set 1

81 set radiusport Set RADIUS port number set radiussecret Set RADIUS shared secret set rate Set Data Rate set rate Set Data Rate set rate

82 set wirelessmode Set Wireless LAN Mode set 80211d Set 802.11d mode set http Set http Enable/Disable set HttpPort Set http port number set

83 set activeCurrentPro-file Set active Current Profile set profileName Set Profile Name set profileVlanId Set Profile Vlan Id set APPrimaryProfile

84 set dhcpMode Set Dhcp Mode set wdsMacList Set WDS Mac Address List set enableWireless-Client Set Wireless Client Enable/Disable set isolationTyp

4 Management Web based configuration RADIUS Accounting RADIUS-On feature RADIUS Accounting update CLI Message Log Access Control list file support Co