Planet Technology SKG-300 Manuel d'utilisateur

Personal VoIP Gateway SKG-300 User Manual 1

When you see the following screen, press the Finish button. 10 Then you will see the following Windows New Hardware Found Wizard screen. Select

When you see the following screen, press the Continue Anyway button. When you will see the following screen, select the option, “allow this prog

12 When you see the following screen, press the Finish button. STEP 3: When the installation completes you should see the following message appe

STEP 4: Connect a standard telephone handset to the SKG-300 phone jack using a telephone cable as shown below STEP 5: Connect a telephone cable

You final configuration should resemble the following. 14

Chapter 3 SKG-300 Configuration 3.1 Enable SKG-300 In order to use SKG-300 and its features, (1) the SKG-300 adapter must be plugged into the PC, (2

You may see the following screen, select the option, “allow this program to use Skype” and press the OK button. You should now see the SKGAgent in

When the SKGAgent is not running, there is no phone in the system tray. 3.2 Testing SKG-300 Skype provides a useful feature to test your connection.

You will see the following chat screen and you should enter “callme” and press the Enter key on your keyboard. Within 10-20 seconds, you should se

When the test concludes you can press OK on the following screen. 19 and then press Finish on the following screen. 3.3 Making and Receiving Cal

Copyright Copyright (C) 2005 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed pr

call, dialing as per the SkypeOut™ recommended dialing sequence, 00 + country code + telephone number (e.g. 00 886 2 22199518) and pressing the aster

21 Step 3: You will now see an indication that the Skype™ contact has a speed dial associated with them as shown below. 3.5 Switching Between Vo

22can do the following: • Press ‘#1’ to answer new call keeping current call on-hold • Press ‘##’ to answer call and terminate current call Once

23 You will see the SKG-300 configuration screen as shown below. Press the Call Forwarding tab to see the Call Forwarding parameters as shown

• Check the Enable Call Forward checkbox as shown below 24 • Select the number of rings before the forwarding takes place as shown below. The

If you are on a PBX, you may need to press a digit to get an outside line (i.e. 9). In this case you would enter 0,,,22199518. In order to forward

3.9 Toll Bypass Toll bypass is similar to forwarding, except the incoming caller hears a beep, enters a password and then dials out an arbitrary numb

27 In order to enable toll bypass of incoming PSTN calls, change the Phone Line to VOIP settings as follows: • Check the Enable Toll Bypass check

28 Set your password and press apply as shown below. The password can be any 4 to 8 digits When you call into your telephone line you will hea

29"Note: You may need to disable suspend mode in your computer to prevent the computer from going into sleep mode. If the computer is in sleep

3Index Chapter 1 Introduction...4

30Automation： Inactive：SKG-300 will not record any voice. Record next call：SKG-300 will only record the next call, and then the Automation sta

User Action Key Repeat current message 1 Delete current message, move to next 2 Keep current message, move to next 3 Delete all messages 9 9.

The Initiate VoIP Call – press these keys to get a VoIP dial-tone. You can now dial a SkypeOut™ call or a Skype™ speed dial call from your telephone

33 When the uninstall indicator disappears, the un-installation is complete. 3.15 Troubleshooting The first step in troubleshooting is to read the

Common Fix If SKG-300 was working OK and suddenly stops working properly (e.g. stops responding to incoming rings or you cannot get a VoIP dial ton

• If the Skype™ application was terminated for any reason while the SKG-300 agent was running, you will need to exit the SKGAgent and then restart i

Check the Audio In and Audio Out list boxes and make sure SKG-300 Skype Audio Device is selected. Call Forwarding is not working properly • Make

Chapter 1 Introduction Thank you for purchasing SKG-300 Personal VoIP Gateway. PLANET provides several types of Skype solution to meet various dem

5¾ Quick Installation Guide ¾ CD-ROM with User’s Manual, Driver and Utility System requirements Minimum System Requirements： ¾ Microsoft Windows

Chapter 2 SKG-300 Setup 2.1 Hardware Details LED Display LED Indicators Descriptions LINK Steady on indicates SKG-300 has correctly connected to

Port Descriptions Line For connecting to PSTN line Phone For connecting to a phone set USB For connecting to a computer or laptop 2.2 SKG-300 utilit

Then you will see the End User License Agreement. Click the “I have read …” checkbox and press the I Agree button as shown below. Wait until you s

9"Note: The SKG-300 Adapter MUST not be connected to a bus powered USB hub. You will see the following Windows New Hardware Found Wizard.